Hard reset: push and hold both the Connect and Reset Buttons at the same time until it turns off -> wait 2 minutes -> turn back on with power button. You can find the LR4 Troubleshooter which includes all other possible errors here. Edit 1: Added text steps. Edit 2: Added Link to LR4 Troubleshooter. Reply.Blue: WiFi is connected, and the unit is ready for the next use. White: WiFi is turned off. Blinking Blue: WiFi is disconnected / reconnecting. Learn more. Blinking Yellow: Unit is in Onboarding Mode. Follow the prompts in the app and scan the QR code on the back of the unit as directed. Press the Connect button to exit Onboarding Mode. Learn more. Select your Litter-Robot 4. Select the Settings gear in the top right corner. Select Update Network. Follow the steps listed within the app. Once the update is complete, your Litter-Robot should be ready for use. If your unit displays a solid blue light bar, you've been successful. If your unit is not displaying a solid blue light bar, your ... Power the unit off. Unplug the power supply from the back of the base. Wait 1 minute. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty ... Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light. Plug the Litter-Robot into the wall. Press the Power button to turn the unit on. Once the initial clean cycle is complete, the unit should return home displaying a blue 'ready light' … Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light. BLUE SOLID . Ready (standby) Cycle doesn't start because cat not detected; Turns blue without cycling when powering up, Circuit board defective; Press down on …Litter-Robot 3: Red light flashing (Cat sensor fault) The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red.The Litter-Robot is equipped with an Anti-Pinch Safety Feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch conditi...Last night’s (Nov. 12) $691.5-million auction at Christie’s broke multiple records. It was the most expensive ever auction and included the most expensive work ever sold, Francis B... Preparation. If Litter-Robot 4 displays a blue light bar with a blinking blue light adjacent to the Connect button, this indicates that the unit is connecting to the app or has disconnected and is trying to reconnect but has not successfully reconnected. Blue and yellow and red (All three lights flashing simultaneously): This means the unit cannot find the Dump or Home position. The unit will not cycle automatically and needs …Litter-Robot 3: Red light flashing (Cat sensor fault) The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red.Find out what makes an experience an NDE, who typically has them and how people have tried to explain them. Advertisement Near-death experiences (NDEs) are common enough that they... If one of these sensors is malfunctioning, the blinking blue light will activate. To fix this issue, check the sensor ports for debris and ensure they are properly connected. If the issue persists, contact Litter Robot customer support for further assistance. 1.4 Importance Of Troubleshooting The Blinking Blue Light. 2 Step 1: Checking The Connection. 3 Step 2: Examining The Waste Drawer. 3.1 Clearing Any Obstructions: 3.2 Checking The Carbon Filter: 3.3 Cleaning The Waste Drawer: 4 Step 3: Reviewing The Sensor. 5 Step 4: Evaluating The Globe.This may take up to 30 minutes to complete. You will see a single white light blinking on your unit’s control panel while your robot’s firmware is updating. Once the update is complete, your Litter-Robot should be ready for use. Successful: If your Litter-Robot displays a blue light bar, you've been successful.Our litter robot was Flashing Yellow Slow & Fast, then Fast Flashing Blue despite being empty and lastly just Random Lights. Watch for the solution to this, ...If it cannot cycle after three attempts, the globe will return to the home position, and the control panel will flash yellow and red or blue and red lights. There are a few things you can do to troubleshoot a …Common Solutions for Litter Robot 3 Blinking Yellow Light: 1. Empty the Waste Drawer: When the waste drawer reaches its limit, the Litter Robot typically alerts users with a blinking yellow light. Addressing this is straightforward: open the drawer, carefully remove the full waste bag, and replace it with a fresh one.The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. There's a lot of dust and debris …So, let’s talk a bit about what you should do when you’re dealing with blinking Litter-Robot 3 lights. 1. Reset the Unit. Pressing the Reset button may solve a number of issues you might encounter with your Litter-Robot 3. So, before you panic and start reading through forums, you should turn your unit off or on. 2. Contact SupportStep 3: Clean the Sensors. If the sensors are not obstructed, it may be necessary to clean them. As you continue to operate the Litter Robot, dust and debris can accumulate on the sensors, causing them to malfunction. To clean the sensors, use a clean, dry cloth to gently wipe away any dust or debris.The Litter-Robot is equipped with an Anti-Pinch Safety Feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch conditi...Oct 19, 2022 ... Is your Litter-Robot 3 stuck mid-cycle, flashing yellow rapidly, or not returning to the Home position properly? You might need to replace ...Why is my litter robot 3 blinking blue light not full? If you’re experiencing problems with your Litter-Robot 3, you may notice the blue light blinking. However, before attempting to fix the issue, it’s recommended that you unplug the power supply and wait for 10 seconds. After that, plug the unit back in and let it finish its cleaning cycle.Litter-Robot Connect units only – look for the WiFi symbol on the control panel. Download the Whisker app and follow the onboarding instructions. Ensure proper placement Power on Add litter Download the app 1 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition).Title: 8.5x5.5 QRG 2016_WEB Created Date: 12/19/2016 10:37:50 AMLitter-Robot 3 is equipped with infrared emitters and sensors located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light.Lights in your peripheral vision, or eye floaters, are most often caused by changes in the jelly-like substance in the eyes due to age, explains the Mayo Clinic. They also might be...If your Litter-Robot 3 is displaying a yellow light flashing quickly, this indicates a cycle has been interrupted by the Anti-Pinch safety feature and you will need to inspect the pinch sensor. Inspect the sensors. The purpose of the pinch sensor is to detect if an object is blocking the waste port during the globe rotation. Constantly getting stuck upside down red and blue flashing lights so you pull the power cord out put it back in let it cycle stays upside down, then clean all of the sensors and it does it over and over again. If we hadn’t spent so much money on I’d just throw it over the fence. I read it was the curtain sensors. Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light. If your unit has a blue light bar with partial yellow flashing or the unit will not cycle, this indicates that the scale has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Place the unit on a firm, level surface. Avoid soft, uneven, or unstable flooring for accurate weight ... Title: 8.5x5.5 QRG 2016_WEB Created Date: 12/19/2016 10:37:50 AMThe Gullah Geechee people painted porch ceilings blue to trick haints into thinking their houses were surrounded by water, which a haint can't cross. Advertisement Creaky footsteps...Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light.More detailed instruction on fixing plastic cover to prevent slow flashing yellow light pinch detect error on litter Robot 3 Open Air, and better rubber band...Litter-Robot 3 flashing blue light. f notice a flashing or blinking blue light on your Litter-Robot 3 control panel, this is the Drawer Full Indicator, which means that the waste drawer is full (or approaching full) and needs to be emptied. After you have emptied the drawer and installed a new liner, hit the Reset button on the control panel ...I went to the litter robot Support and filled the steps. By doing a hard reset (unplugging the back of the unit for ten seconds) it was resolved. 1. Reply. Share. Ever since I changed the last bag, my litter robot 3 has had its blue light blinking after every use. I can hit reset and it stops, until the next….The shield is a possible cause for the three lights flashing fault. We strongly recommend removing the internal shield. If your Litter-Robot was built before February of 2018, you may have an internal shield. The internal shield is not necessary for the unit to function and was removed from the design in March 2018.May 1, 2017 ... Catz: Litter Robot 3 blue flashing light, drawer empty, circuit boards cleaned; dfi replacement. Experimental FunZ•890 views · 12:25 · Go to ...The NHS Blue Light Card program is an initiative designed to show appreciation and support for the hardworking emergency services, NHS, and armed forces personnel in the United Kin...Details. Say goodbye to scooping and give your cats clean litter every time they go with Litter-Robot 3, the highest-rated automatic litter box. Purchase includes a 90-day in-home trial, comprehensive coverage with our WhiskerCare™ 1-Year Warranty, and free shipping (excl. AK, HI, PR). Never scoop again®. Helps reduce litter box odors.To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit should start its cleaning cycle and goes back to solid blue. If it did, the issue must be caused by the drawer liner not being properly tucked into the tabs. Please check the following video:Status Indicator Lights. Solid Blue: Feeder is in Automatic Feeding Mode. Solid Yellow: Hopper is low indicating less than 20% food remaining. Solid Red: Hopper is critically low indicating less than 5% food remaining. Flashing Red: Dispenser is jammed. Solid Purple: Food Bowl and Food Chute are full for 12+ hours (food has not been consumed)Without further description, let’s dig deeper into the fast-blinking issues of Litter Robots. We can categorize the troubleshooting session into two segments. Because the robot blinks in three colors, (If you are here seeking an answer for ‘why is my litter robot 3 blinking blue light?’ You’ll also find the answers here.When I turn on the Litter Robot 3 (non-connect), blue light is flashing, then I press Reset and fast yellow light is flashing. When I press Reset again, blue light is flashing and so on.. What I checked so far: - Anti Pinch Pins looks good and are touching each other. - DFI is clean and 4 IR LEDs are blinking once a second.The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. There's a lot of dust and debris which can cause issues, which leads to the robot not ...The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. There's a lot of dust and debris …If you work for the NHS or emergency services, you may already be familiar with the NHS Blue Light Card. This valuable discount program offers exclusive savings to those who dedica...Garbage products. I would suggest if you are considering purchasing a Litter-Robot that you do not buy one. They are too expensive to not work as often as it does not work. Our cat doesn't even fit in the damn thing. So woke up this morning with litter robot 4 offline. The big light is solid blue with the little light flashing blue.Blue: WiFi is connected, and the unit is ready for the next use. White: WiFi is turned off. Blinking Blue: WiFi is disconnected / reconnecting. Learn more. Blinking Yellow: Unit is in Onboarding Mode. Follow the prompts in the app and scan the QR code on the back of the unit as directed. Press the Connect button to exit Onboarding Mode. Learn more.When a cat enters the globe, the cat sensor is activated; the blue light turns off and the red light turns on. Once the cat exits the globe, the countdown to a Clean cycle begins. ... If your Litter-Robot is flashing red or stuck upside down, complete the troubleshooting steps in our Litter-Robot 3: Red light flashing (Cat sensor fault) guide.If your unit has a blue light bar with partial yellow flashing or the unit will not cycle, this indicates that the scale has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Place the unit on a firm, level surface. Avoid soft, uneven, or unstable flooring for accurate weight ...Do you have a pair of shoes that aren't worn out, but are just too smelly to wear? You could buy any number of de-smelling solutions from your local big box store, but we head stra...May 8, 2019 · Here's what I told Litter Robot, " Every time it’s used, it half cycles and I have to power it off and power it back on for it to cycle. Pushing the “cycle” ... If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. Successful: If your unit returned home and displays a solid blue light, you've been successful. The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ... Step 3: Check the Power Cord. If the waste drawer is not full and the sensors are clean, the next step is to check the power cord. A frayed or damaged power cord can cause the Litter Robot to malfunction and the yellow light to flash rapidly. Make sure the power cord is securely plugged into the unit and the outlet, and check for any damage ...Objects are resting or pressing on the unit. The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. To test your changes, power the unit off and then on. Allow the unit to complete the start‐up cycle and return Home with a solid blue light. Your unit is operating normal.If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful. If your unit is not displaying a solid blue light after ...Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light. These sensors detect when a cat has entered or exited the unit. If the unit detects an issue with all three laser sensors, called curtain sensors, it will indicate a fault with the entire system and the light bar on the Litter-Robot will display red and blue alternating lights. You will also receive a notification on your phone if you use the ... After troubleshooting for blinking blue light, I replaced the dfi sensor. However, after the replacement, I am getting the blue yellow red sequential blinking. The motor wheel is not loose and I have done all other checks. I even reset the cat sensor. ... Litter robot 3 question Im hoping someone can help me. My male cat can pee over the … Short press the Reset button, then short press the Cycle button to run a Clean cycle. After Litter-Robot cycles, it should return to the Home position, displaying a blue light bar. Successful: If your unit displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a green light bar with partial red flashing, please ... Hard reset: push and hold both the Connect and Reset Buttons at the same time until it turns off -> wait 2 minutes -> turn back on with power button. You can find the LR4 Troubleshooter which includes all other possible errors here. Edit 1: Added text steps. Edit 2: Added Link to LR4 Troubleshooter. Reply.A blue pitbull is an American pitbull terrier with a blue-colored coat. The color can range in hue from a light gray-blue shade to a dark charcoal color. The nose is gray in color ...The tray's empty and the light still blinks with or without a bag. None of the buttons work and there's no start up cycle when I switch it on and off. The lights flash sequentially when it boots up, but it always settles on a blinking blue light. I can still switch the Litter Robot on and off via the app but I can't do anything else.Power the unit off. Unplug the power supply from the back of the base. Wait 1 minute. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty ... Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Chat with us 1-877-250-7729 Submit a ticket. Discover troubleshooting tips for your Litter-Robot 4 in solid blue ready mode. Browse our support guide to ensure optimal use. Now, the “ready” light flashes blue and when I press the reset button, the “cycling” light flashes yellow/amber rapidly. I Googled this and seems to be an indicator that the weight or anti-pinch sensors are being tripped (based on the flashing yellow/amber “cycling” light). I unplugged the robot and disassembled and used a q-tip to ...Jun 12, 2018 · robotshopTech June 12, 2018, 3:52pm 1. If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS ... Select your Litter-Robot 4. Select the Settings gear in the top right corner. Select Update Network. Follow the steps listed within the app. Once the update is complete, your Litter-Robot should be ready for use. If your unit displays a solid blue light bar, you've been successful. If your unit is not displaying a solid blue light bar, your ...The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit …If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. Successful: If your unit returned home and displays a solid blue light, you've been successful.If it cannot cycle after three attempts, the globe will return to the home position, and the control panel will flash yellow and red or blue and red lights. There are a few things you can do to troubleshoot a …Preparation. If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app.. You can now proceed with the onboarding process within the Whisker App to finalize connection.. When your Litter-Robot 4 has successfully …Easy fix for three solid green lights, and two flashing red, which is cat sensor fault. I just got off the phone with the litter robot experts. The three open circles at the top of the ring have the sensors behind them. and they are very sensitive to obstruction from cat hair or debris. Mine appeared clean, but apparently were not.Just got a new LR4 and for some reason, I turn it on and it flashes blue and red lights (like a police car). Although the lights look dim and aren't at full brightness. I'm not doing anything else and I can't find this light combo in the manual. It doesn't do a clean cycle on startup. It doesn't cycle when I press the the Cycle or Empty buttons ...Step 8: Connect it and test. Most of you are here because there are 3 flashing lights on your Litter-Robot's control panel. Sometimes this problem is caused by a faulty power supply or the motor itself. If even …pjutras May 6, 2019, 1:53pm 6. Hi, The blue light will blink to indicate that the Drawer is full. If the blue light is blinking after each cycle even when you press the reset button, this mean that either there is something obstructing the way between the 2 DFI sensors or that the sensors themselves are defective.Preparation. If Litter-Robot 4 displays a blue light bar with a blinking blue light adjacent to the Connect button, this indicates that the unit is connecting to the app or has disconnected and is trying to reconnect but has not successfully reconnected.Litter-Robot 3: Red light flashing (Cat sensor fault) The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red.Understanding the Three Blinking Lights on the Litter-Robot 3: A Comprehensive Guide. The Litter-Robot 3, an innovative self-cleaning litter box, features three blinking lights that serve as indicators of its status and potential issues. These lights play a crucial role in ensuring the proper functioning of the Litter-Robot 3 and …Litter-Robot 3: Red light flashing (Cat sensor fault) The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red.Apr 25, 2022 · Without further description, let’s dig deeper into the fast-blinking issues of Litter Robots. We can categorize the troubleshooting session into two segments. Because the robot blinks in three colors, (If you are here seeking an answer for ‘why is my litter robot 3 blinking blue light?’ You’ll also find the answers here. I recently purchased a litter robot 3 connected and the litter robot has been working perfectly up to this point, however, since I did my first litter empty the unit will not reset properly. I have the flashing blue light constantly. I press the reset button and I can get the blue light to remain steady but after one cycle it is back to flashing and …The Takata airbag recall back in 2013 occurred after Safety Restraint Systems (SRS) warning lights started turning on and flashing on the dash in a number of vehicles. Tests reveal...Dec 13, 2022 ... If you get a flashing blue light on your cat box and do not want to spend $80 for a new DFI sensor, then try this fix for $10 in parts.
The Litter-Robot is equipped with an Anti-Pinch Safety Feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch conditi.... Trenten montero rodeo accident
The tray's empty and the light still blinks with or without a bag. None of the buttons work and there's no start up cycle when I switch it on and off. The lights flash sequentially when it boots up, but it always settles on a blinking blue light. I can still switch the Litter Robot on and off via the app but I can't do anything else. Disconnect the bonnet. Gently flex the two front bonnet tabs outward and hold for about 20-30 seconds. Reattach the bonnet. There are four tabs total: two in the back, two on the sides. You should feel a secure snap and hear a “click” when placed back into the slot, and the bonnet should sit closer to the base.Litter-Robot 4 user? Visit our support guiding on troubleshooting Litter-Robot 4 lights. Litter-Robot 3 illumination: Quick reference guide. If you’re looking for a quick view guide on show the Litter-Robot 3 lights, download one digital guide here alternatively click on the image below. Litter-Robot 3 flashing blue daylightJust got a new LR4 and for some reason, I turn it on and it flashes blue and red lights (like a police car). Although the lights look dim and aren't at full brightness. I'm not doing anything else and I can't find this light combo in the manual. It doesn't do a clean cycle on startup. It doesn't cycle when I press the the Cycle or Empty buttons ...Dec 10, 2021 · 1. Empty the Drawer. On the Litter-Robot, you have a drawer that collects the cat litter. If it becomes full, the blue light will blink rapidly. But if you throw out the mess, the lights should go off. Before returning the drawer to its compartment, remember to place a new liner into the container. pjutras May 6, 2019, 1:53pm 6. Hi, The blue light will blink to indicate that the Drawer is full. If the blue light is blinking after each cycle even when you press the reset button, this mean that either there is something obstructing the way between the 2 DFI sensors or that the sensors themselves are defective.These sensors detect when a cat has entered or exited the unit. If the unit detects an issue with all three laser sensors, called curtain sensors, it will indicate a fault with the entire system and the light bar on the Litter-Robot will display red and blue alternating lights. You will also receive a notification on your phone if you use the ...Litter-Robot 3: Cat sensor troubleshooting. The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. When a cat enters the globe, the cat sensor is activated; the blue light turns off and the red light turns on. Once the cat exits the globe, the countdown to a Clean cycle begins.This video shows you how to get the 3 lights on the Litter-Robot 3 to stop blinking. Litter-Robot 3 Buying Options: 💵 Worried about your cats using it? Wan...MNPistagnesi December 3, 2021, 12:00am 1. The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be …Jun 20, 2018 ... Litter Robot 3 Fast Flashing Blue & Random lights - Repair Guide ... How To Fix a Red Flashing Light on a Litter-Robot 3. MAGS How To Videos•17K ...The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red. You will also receive a notification on your phone if you ...Here is the solution they provided, and now my litter robot is finally back to solid blue: "Here are the steps. Remove the bonnet → set aside the globe → place the bonnet back on. Press cycle. When the cycle ends, all three lights will flash on the control panel. Next, unplug the robot from the back of the base (not the wall) while it is ...1.4 Importance Of Troubleshooting The Blinking Blue Light. 2 Step 1: Checking The Connection. 3 Step 2: Examining The Waste Drawer. 3.1 Clearing Any Obstructions: 3.2 Checking The Carbon Filter: 3.3 Cleaning The Waste Drawer: 4 Step 3: Reviewing The Sensor. 5 Step 4: Evaluating The Globe.The shield is a possible cause for the three lights flashing fault. We strongly recommend removing the internal shield. If your Litter-Robot was built before February of 2018, you may have an internal shield. The internal shield is not necessary for the unit to function and was removed from the design in March 2018.So I am having this issue again!!! My litter robot 3 had been flashing blue light and then yellow light (very fast) after pressing the reset button. I’ve read some troubleshooting to check for the metal pinch bars to be in contact all the time. I’ve tried to clean it and it appears to be in contact as well. The pin is not corroded as well.Just got a new LR4 and for some reason, I turn it on and it flashes blue and red lights (like a police car). Although the lights look dim and aren't at full brightness. I'm not doing anything else and I can't find this light combo in the manual. It doesn't do a clean cycle on startup. It doesn't cycle when I press the the Cycle or Empty buttons ...Wood Pellets are a byproduct of the timber industry; you can get a 40lb sack of them for around $4-6 in the US. They are commonly used as fuel for stoves or as livestock bedding. M...Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 ….